Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing happened? Look within the tank, and you might see no water inside. Before you panic, rest easy that fixing this challenge is usually straightforward. If you can’t do it yourself, you can always set up toilet repair with an experienced plumber. Follow these guidelines to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first step is to ensure that the water is flowing. If you or someone in your household recently did a toilet repair, you most likely turned off the water first. Did you not realize you had to turn it back on? To see, spin the water shut-off valve on the wall behind the toilet. If the valve was closed, water should now start refilling the tank. If this doesn’t work, turn on the water at your sink or an alternative plumbing fixture. If nothing flows from the tap, you might have a larger water supply issue. Phone your water company to learn more. 

Reposition or Replace the Float Mechanism 

Older toilet brands use a float ball to measure the water level as it rises in the tank. When the ball passes a specific height, the float arm it’s attached to stops the water flow. However, insufficient water might enter the tank if the ball is positioned incorrectly or the arm is broken. To correct the float ball, start by removing the toilet tank cover. Bend the float arm up a little to adjust where it sits in the tank. If this does not fix the problem, you might need to replace the entire float mechanism. You should be able to perform this yourself by following the instructions that come with the replacement parts, or you can work with a plumber for help. Just understand that float balls are old toilet technology. You may prefer improved dependability and efficiency if you upgrade the existing tank components or replace the toilet altogether. 

Adjust the Fill Valve 

More recent toilets use a float cup instead of a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become clogged. Here are some to attempt: 

• Test the fill valve: Have a look inside the toilet and find the fill valve on top of a vertical tube device on the left side of the tank. Verify that it’s secure and evenly ahered to the tube. Then, change the water level. Newer toilets have an adjustment knob you can turn with your hand, while older designs may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to test the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other crud could be blocking the valve and preventing your toilet from filling. Shut off the water behind the toilet and take off the fill cap. Then, steadily turn the water back on, cupping your hand over the valve to prevent water from spraying everywhere. After several seconds, turn the water back off. Finally, clean off the fill cap to dislodge any hard water buildup. If the cap is broken, buy a new one. 
• Clean the valve tube: The tube below the fill valve may also be plugged. Shut off the water and take off the valve hardware. Then, place a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the debris. Replace the valve hardware and flush the toilet to test your work. 

Repair or Replace the Trip Assembly 

If you’ve followed the steps above without success, the final possibility is a faulty trip assembly. This component attaches the flush handle to the tank. If it’s not working or positioned inadequately, the flush cycle may not complete, leaving the tank empty. Remove the toilet tank lid and look at the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is crooked, worn or wrecked, replace it. Whether you perform the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water once more. 

Schedule Toilet Repair Today 

You can’t go long without a reliable toilet, so call [Company name] to schedule a toilet repair. We can diagnose why your toilet isn’t filling and propose the appropriate fix. If your plumbing fixture is older and worn out, our team can install a high-efficiency toilet in its place. Rest assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed crews, please call your community Service Experts Heating, Air Conditioning & Plumbing office today.